Glass electrode

China Suppliers


Types

Almost all commercial electrodes respond to single charged ions, like H+, Na+, Ag+. The most common glass electrode is the pH-electrode. Only a few chalcogenide glass electrodes are sensitive to double-charged ions, like Pb2+, Cd2+ and some others.

There are two main glass-forming systems: paving concrete block

silicate matrix based on molecular network of silicon dioxide (SiO2) with additions of other metal oxides, such as Na, K, Li, Al, B, Ca, etc. flagstone flooring

chalcogenide matrix based on molecular network of AsS, AsSe, AsTe. pavers pool deck

Interfering ions

Because of the ion-exchange nature of the glass membrane, it is possible for some other ions to concurrently interact with ion-exchange centers of the glass and to distort the linear dependence of the measured electrode potential on pH or other electrode function. In some cases it is possible to change the electrode function from one ion to another. For example, some silicate pNa electrodes can be changed to pAg function by soaking in a silver salt solution.

Interference effects are commonly described the semiempirical Nicolsky-Eisenman equation (also known as Nikolsky-Eisenman equation), an extension to the Nernst equation. It is given by

where E is the emf, E0 the standard electrode potential, z the ionic valency including the sign, a the activity, i the ion of interest, j the interfering ions and kij is the selectivity coefficient. The smaller the selectivity coefficient, the less is the interference by j.

To see the interfering effect of Na+ to a pH-electrode:

Range of a pH glass electrode

The pH range at constant concentration can be divided into 3 parts:

Scheme of the typical dependence E-pH for ion-selective electrode

Complete realization of general electrode function, where dependence of potential on pH has linear behavior and within which such electrode really works as ion-selective electrode for pH.

Alkali error range - at low concentration of hydrogen ions (high values of pH) contributions of interfering alkali metals (like Li, Na, K) are comparable with the one of hydrogen ions. In this situation dependence of the potential on pH become non-linear.

The effect is usually noticeable at pH > 12, and concentrations of lithium or sodium ions of 0.1 moles per litre or more. Potassium ions usually cause less error than sodium ions.

Acidic error range - at very high concentration of hydrogen ions (low values of pH) the dependence of the electrode on pH becomes non-linear and the the influence of the anions in the solution also becomes noticeable. These effects usually become noticeable at pH  < 1.

There are different types of pH glass electrode, some of them have improved characteristics for working in alkaline or acidic media. But almost all electrodes have sufficient properties for working in the most popular pH range from pH=2 to pH=12. Special electrodes should be used only for working in aggressive conditions.

Most of text written above is also correct for any ion-exchange electrodes.

Construction

Scheme of typical pH glass electrode

a sensing part of electrode, a bulb made from a specific glass

sometimes the electrode contains a small amount of AgCl precipitate inside the glass electrode

internal solution, usually 0.1 mol/L HCl for pH electrodes or 0.1 mol/L MeCl for pMe electrodes

internal electrode, usually silver chloride electrode or calomel electrode

body of electrode, made from non-conductive glass or plastics.

reference electrode, usually the same type as 4

junction with studied solution, usually made from ceramics or capillary with asbestos or quartz fiber.

A typical modern pH probe is a combination electrode, which combines both the glass and reference electrodes into one body. The bottom of a pH electrode balloons out into a round thin glass bulb. The pH electrode is best thought of as a tube within a tube. The inside most tube (the inner tube) contains an unchanging saturated KCl and a 0.1 mol/L HCl solution. Also inside the inner tube is the cathode terminus of the reference probe. The anodic terminus wraps itself around the outside of the inner tube and ends with the same sort of reference probe as was on the inside of the inner tube. Both the inner tube and the outer tube contain a reference solution but only the outer tube has contact with the solution on the outside of the pH probe by way of a porous plug that serves as a salt bridge.

The details of this section describe the functioning of two separate types of glass electrodes as one unit. It needs clarification.

This device is essentially a galvanic cell. The reference end is essentially the inner tube of the pH meter, which for obvious reasons cannot lose ions to the surrounding environment (as a reference is good only so long as it stays static through the duration of the measurement). The outer tube contains the medium, which is allowed to mix with the outside environment (and as a consequence this tube must be replenished with a solution of KCl due to ion loss and evaporation).

The measuring part of the electrode, the glass bulb on the bottom, is coated both inside and out with a ~10 nm layer of a hydrated gel. These two layers are separated by a layer of dry glass. The silica glass structure (that is, the conformation of its atomic structure) is shaped in such a way that it allows Na+ ions some mobility. The metal cations (Na+) in the hydrated gel diffuse out of the glass and into solution while H+ from solution can diffuse into the hydrated gel. It is the hydrated gel, which makes the pH electrode an ion selective electrode.

H+ does not cross through the glass membrane of the pH electrode, it is the Na+ which crosses and allows for a change in free energy. When an ion diffuses from a region of activity to another region of activity, there is a free energy change and this is what the pH meter actually measures. The hydrated gel membrane is connected by Na+ transport and thus the concentration of H+ on the outside of the membrane is 'relayed' to the inside of the membrane by Na+.

All glass pH electrodes have extremely high electric resistance from 50 to 500 M. Therefore, the glass electrode can be used only with a high input-impedance measuring device like a pH meter, or, more generically, a high input-impedance voltmeter which is called an electrometer.

Storage

Between measurements any glass and membrane electrodes should be kept in the solution of its own ion (Ex. pH glass electrode should be kept in 0.1 mol/L HCl or 0.1 mol/L H2SO4). It is necessary to prevent the glass membrane from drying out.

See also

Wikimedia Commons has media related to: Glass electrode

pH

pH meter

Potentiometry

Ion-selective electrodes

Chalcogenide glass

Quinhydrone electrode

References

^ D. G. Hall, Ion-Selective Membrane Electrodes: A General Limiting Treatment of Interference Effects, J. Phys. Chem 100, 7230 - 7236 (1996) article

Ludwig Kratz: Die Glaselektrode und ihre Anwendungen (Steinkopf, Frankfurt, 1950)

External links

pH electrode practical/theoretical information

Titration with the glass electrode and pH calculation - freeware

v  d  e

Glass science topics

Basics

Glass definition  Is glass a liquid or a solid?  Glass-liquid transition  Physics of glass  Supercooling

Glass formulation

AgInSbTe  Bioglass  Borophosphosilicate glass  Borosilicate glass  Ceramic glaze  Chalcogenide glass  Cobalt glass  Cranberry glass  Crown glass  Flint glass  Fluorosilicate glass  Fused quartz  GeSbTe  Gold ruby glass  Lead glass  Milk glass  Phosphosilicate glass  Photochromic lens glass  Silicate glass  Soda-lime glass  Sodium hexametaphosphate  Soluble glass  Ultra low expansion glass  Uranium glass  Vitreous enamel  ZBLAN

Glass-ceramics

Bioactive glass  CorningWare  Glass-ceramic-to-metal seals  Macor  Zerodur

Glass preparation

Annealing  Chemical vapor deposition  Glass batch calculation  Glass forming  Glass melting  Glass modeling  Ion implantation  Liquidus temperature  Sol-gel technique  Viscosity

Optics

Achromat  Dispersion  Gradient index optics  Hydrogen darkening  Optical amplifier  Optical fiber  Optical lens design  Photochromic lens  Photosensitive glass  Refraction  Transparent materials

Surface modification

Anti-reflective coating  Chemically strengthened glass  Corrosion  Dealkalization  DNA microarray  Hydrogen darkening  Insulated glazing  Porous glass  Self-cleaning glass  Sol-gel technique  Toughened glass

Diverse topics

Diffusion  Glass-coated wire  Glass databases  Glass electrode  Glass fiber reinforced concrete  Glass history  Glass ionomer cement  Glass microspheres  Glass-reinforced plastic  Glass science institutes  Glass-to-metal seal  Porous glass  Prince Rupert's Drops  Radioactive waste vitrification  Windshield

Categories: Electrodes | Electrochemistry | Glass applications