Investment casting

China Suppliers


Process

Casts can be made of the wax model itself, the direct method; or of a wax copy of a model that need not be of wax, the indirect method. The following steps are for the indirect process, which, in total, can take two days to one week to complete.

Produce a master pattern: An artist or mold-maker creates an original pattern from wax, clay, wood, plastic, steel, or another material. heavy duty caster

Moldmaking: A mold, known as the master die, is made of the master pattern. The master pattern may be made from a low-melting-point metal, steel or wood. If a steel pattern was created then a low-melting-point metal may be cast directly from the master pattern. Rubber molds can also be cast directly from the master pattern. The first step may also be skipped if the master die is machined directly into steel. stem casters

Produce the wax patterns: Although called a wax pattern pattern materials also include plastic and frozen mercury. Wax patterns may be produced in one of two ways. In one process the wax is poured into the mold and swished around until an even coating, usually about 3 mm (0.12 in) thick, covers the inner surface of the mold. This is repeated until the desired thickness is reached. Another method is filling the entire mold with molten wax, and let it cool, until a desired thickness has set on the surface of the mold. After this the rest of the wax is poured out again, the mold is turned upside down and the wax layer is left to cool and harden. With this method it is more difficult to control the overall thickness of the wax layer.[citation needed] sushi conveyor belt

If a core is required, there are two options: soluble wax or ceramic. Soluble wax cores are designed to melt out of the investment coating with the rest of the wax pattern, whereas ceramic cores remain part of the wax pattern and are removed after the workpiece is cast.

Assemble the wax patterns: The wax pattern is then removed from the mold. Depending on the application multiple wax patterns may be created so that they can all be cast at once. In other applications, multiple different wax patterns may be created and then assembled into one complex pattern. In the first case the multiple patterns are attached to a wax sprue, with the result known as a pattern cluster, or tree; as many as several hundred patterns may be assembled into a tree. Foundries often use registration marks to indicate exactly where they go.[citation needed] The wax patterns are attached to the sprue or each other by means of a heated metal tool. The wax pattern may also be chased, which means the parting line or flashing are rubbed out using the heated metal tool. Finally it is dressed, which means any other imperfections are addressed so that the wax now looks like the finished piece.

Investment: The ceramic mold, known as the investment, is produced by three repeating steps: coating, stuccoing, and hardening. The first step involves dipping the cluster into a slurry of fine refractory material and then letting any excess drain off, so a uniform surface is produced. This fine material is used first to give a smooth surface finish and reproduce fine details. In the second step, the cluster is stuccoed with a coarse ceramic particle, by dipping it into a fluidised bed, placing it in a rainfall-sander, or by applying by hand. Finally, the coating is allowed to harden. These steps are repeated until the investment is the required thickness, which is usually 5 to 15 mm (0.2 to 0.6 in). Note that the first coatings are known as prime coats. An alternative to multiple dips is to place the cluster upside-down in a flask and then liquid investment material is poured into the flask. The flask is then vibrated to allow entrapped air to escape and help the investment material fill in all of the details.

Common refractory materials used to create the investments are: silica, zircon, various aluminium silicates, and alumina. Silica is usually used in the fused silica form, but sometimes quartz is used because it is less expensive. Aluminium silicates are a mixture of alumina and silica, where commonly used mixtures have an alumina content from 42 to 72%; at 72% alumina the compound is known as mullite. During the primary coat(s), zircon-based refractories are commonly used, because zirconium is less likely to react with the molten metal. Chamotte is another refractory material that has been used.[citation needed] Prior to silica, a mixture of plaster and ground up old molds (chamotte) was used.

The binders used to hold the refractory material in place include: ethyl silicate (alcohol-based and chemically set), colloidal silica (water-based, also known as silica sol, set by drying), sodium silicate, and a hybrid of these controlled for pH and viscosity.

Dewax: The investment is then allowed to completely dry, which can take 16 to 48 hours. Drying can be enhanced by applying a vacuum or minimizing the environmental humidity. It is then turned upside-down and placed in a furnace or autoclave to melt out and/or vaporize the wax. Most shell failures occur at this point because the waxes used have a thermal expansion coefficient that is much greater than the investment material surrounding it, so as the wax is heated it expands and induces great stresses. In order to minimize these stresses the wax is heated as rapidly as possible so that the surface of the wax can melt into the surface of the investment or run out of the mold, which makes room for the rest of the wax to expand. In certain situations holes may be drilled into the mold beforehand to help reduce these stresses. Any wax that runs out of the mold is usually recovered and reused.

Burnout & preheating: The mold is then subjected to a burnout, which heats the mold between 870 C and 1095 C to remove any moisture and residual wax, and to sinter the mold. Sometimes this heating is also as the preheat, but other times the mold is allowed to cool so that it can be tested. If any cracks are found they can be repaired with ceramic slurry or special cements. The mold is preheated to allow the metal to stay liquid longer to fill any details and to increase dimensional accuracy, because the mold and casting cool together.

Pouring: The investment mold is then placed cup-upwards into a tub filled with sand. The metal may be gravity poured, but if there are thin sections in the mold it may be filled by applying positive air pressure, vacuum cast, tilt cast, pressure assisted pouring, or centrifugal cast.

Removal: The shell is hammered, media blasted, vibrated, waterjeted, or chemically dissolved (sometimes with liquid nitrogen) to release the casting. The sprue is cut off and recycled. The casting may then be cleaned up to remove signs of the casting process, usually by grinding.

The investment shell for casting a turbocharger rotor

A view of the interior investment shows the smooth surface finish and high level of detail

The completed workpiece

Counter-gravity pouring

A variation on the pouring technique is to fill the investment upside-down. A common form of this is called the Hitchiner process, which is named after the Hitchiner Manufacturing Company that invented the technique. In this technique the investment shell is placed in a vacuum tight mold chamber and then lowered into a pool of molten metal. A vacuum is then created, which draws the metal up into the investment shell. After the casting has solidified the vacuum is released, which allows any remaining liquid metal to flow back into the pool.

This technique is more metal efficient than traditional pouring because less material solidifies in the gating system. Gravity pouring only has a 15 to 50% metal yield as compared to 60 to 95% for counter-gravity pouring. There is also less turbulence, so the gating system can be simplified since it doesn't have to control turbulence. Plus, because the metal is drawn from below the top of the pool the metal is free from dross and slag, as these are lower density (lighter) and float to the top of the pool. The pressure differential helps the metal flow into every intricacy of the mold. Finally, lower temperatures can be used, which improves the grain structure.

This process is also used to cast refractory ceramics under the term vacuum casting.

Vacuum pressure casting

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (February 2010)

Vacuum pressure casting (VPC) is a recent development in metal casting, whereby vacuum is used in combination with various gases under pressure to improve the quality of the casting and minimize porosity in the metal. Typically VPC casting machines consist of an upper and a lower chamber. The upper chamber or melting chamber housing the crucible, and the lower casting chamber housing the investment mould. Both chambers are connected via a small hole containing a stopper. A computer program governs the various cycles involved in the casting process. A typical casting cycle, would progress as follows:

The preheated investment mould is placed in the casting chamber which is then closed tight.

The metal casting granules are then placed into a graphite crucible in the melting chamber. The melting chamber is also closed with an airtight seal.

The air in the chambers is then evacuated

The chamber is then filled with an inert gas, such as Helium to prevent oxidation of the metal alloy during the melting stage.

The casting alloy is then heated up to the desired casting temperature

Upon reaching the desired temperature, the melting gas Helium is evacuated from the chamber, immediately after which the crucible stopper is lifted, allowing the molten alloy to flow under the force of gravity into the mould.

Immediately after the pour, the upper chamber is pressurised with Argon gas, which effectively pushes the molten alloy into the mould, ensuring that any shrinkage porosity is minimised.

Once the casting alloy has solidified in the mould, the chambers can be depressurised and opened, allowing for the removal of the casting.

Details

Investment casting is used with almost any castable metal, however aluminium alloys, copper alloys, and steel are the most common. In industrial usage the size limits are 3 g (0.1 oz) to about 5 kg (11 lb). The cross-sectional limits are 0.6 mm (0.024 in) to 75 mm (3.0 in). Typical tolerances are 0.1 mm for the first 25 mm (0.005 in for the first inch) and 0.02 mm for the each additional centimeter (0.002 in for each additional inch). A standard surface finish is 1.34 microns (50125 in) RMS.

The advantages of investment casting are:

Excellent surface finish

High dimensional accuracy

Extremely intricate parts are castable

Almost any metal can be cast

No flash or parting lines

The main disadvantage is the overall cost. Some of the reasons for the high cost include specialized equipment, costly refractories and binders, many operations to make a mold, a lot of labor is needed and occasional minute defects.

History

This section does not cite any references or sources.

Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. (March 2009)

The history of lost-wax casting dates back thousands of years. Its earliest use was for idols, ornaments and jewellery, using natural beeswax for patterns, clay for the moulds and manually operated bellows for stoking furnaces. Examples have been found across the world in India's Harappan Civilisation (25002000 BC) idols, Egypt's tombs of Tutankhamun (13331324 BC), Mesopotamia, Aztec and Mayan Mexico, and the Benin civilization in Africa where the process produced detailed artwork of copper, bronze and gold.

The earliest known text that describes the investment casting process (Schedula Diversarum Artium) was written around 1100 A.D. by Theophilus Presbyter, a monk who described various manufacturing processes, including the recipe for parchment. This book was used by sculptor and goldsmith Benvenuto Cellini (15001571), who detailed in his autobiography the investment casting process he used for the Perseus with the Head of Medusa sculpture that stands in the Loggia dei Lanzi in Florence, Italy.

Investment casting came into use as a modern industrial process in the late 19th century, when dentists began using it to make crowns and inlays, as described by Dr. D. Philbrook of Council Bluffs, Iowa in 1897. Its use was accelerated by Dr. William H. Taggart of Chicago, whose 1907 paper described his development of a technique. He also formulated a wax pattern compound of excellent properties, developed an investment material, and invented an air-pressure casting machine.

In the 1940s, World War II increased the demand for precision net shape manufacturing and specialized alloys that could not be shaped by traditional methods, or that required too much machining. Industry turned to investment casting. After the war, its use spread to many commercial and industrial applications that used complex metal parts. Sturm, Ruger, founded in 1949, rose to dominance in firearms manufacturing by using the new technology to reduce labor-intensive machining.[citation needed]

Modern investment casting techniques stem from the development in the United Kingdom of a shell process using wax patterns known as the investment X process.[citation needed] This method resolved the problem of wax removal by enveloping a completed and dried shell in a vapor degreaser. The vapor permeated the shell to dissolve and melt the wax. This process has been evolved over years into the current process of melting out the virgin wax in an autoclave or furnace.

Applications

Investment casting is used in the aerospace and power generation industries to produce turbine blades with complex shapes or cooling systems. Blades produced by investment casting can include single-crystal (SX), directionally solidified (DS), or conventional equiaxed blades. Investment casting is also widely used by firearms manufacturers to fabricate firearm receivers, triggers, hammers, and other precision parts at low cost. Other industries that use standard investment-cast parts include military, medical, commercial and automotive.

See also

Full-mold casting

Lost-foam casting

References

Notes

^ Investment Casting Process Description

^ a b c d e f Degarmo, Black & Kohser 2003, p. 317.

^ ASM Handbook, p. 257.

^ Dvorak, Donna (May 2008), "The Not-So-Lost Art of Lost Wax Casting", Copper in the Arts (13), http://www.copper.org/consumers/arts/2008/may/supplement.html .

^ a b ASM Handbook, pp. 257258.

^ Sias 2006, pp. 1314.

^ a b ASM Handbook, pp. 261262.

^ a b c Degarmo, Black & Kohser 2003, p. 318.

^ a b Degarmo, Black & Kohser 2003, pp. 319320.

^ Mitchell, Brian S. (2004), An introduction to materials engineering and science for chemical and materials engineers, Wiley-IEEE, p. 725, ISBN 9780471436232, http://books.google.com/books?id=ecimZRLnGcEC&pg=PA725. 

^ a b c d Degarmo, Black & Kohser 2003, p. 319.

Bibliography

American Society for Metals; ASM International Handbook Committee; ASM International Alloy Phase Diagram Committee (1990), ASM Handbook: Casting, 15 (10th ed.), ASM International, ISBN 9780871700216, http://books.google.com/books?id=KCUjfz-ILSEC .

Degarmo, E. Paul; Black, J T.; Kohser, Ronald A. (2003), Materials and Processes in Manufacturing (9th ed.), Wiley, ISBN 0-471-65653-4 .

Sias, Fred R. (2006), Lost-wax Casting: Old, New, and Inexpensive Methods (illustrated ed.), Woodsmere Press, ISBN 9780967960005, http://books.google.com/books?id=e_09Enaf4tIC .

External links

"The Spectrum of Investment Casting Possibilities: PMI Alloy and Engineering Guide". Precision Metalsmiths, Inc. http://www.precisionmetalsmiths.com/PMIalloyEngineeringGuide.pdf. Retrieved 2009-02-23. 

Flash animation of the investment casting process

Investment Castings & Lost Wax Casting Video

v  d  e

Metalworking

 

Casting

Processes

Billet  Centrifugal  Continuous  Die  Investment (Lost wax)  Lost foam  Sand  Shaw process  Spin  Tilt  Vacuum

Furnaces

Bessemer  Blast  Cupola  Electric arc  Electric induction  Open hearth  Puddling  Reverberatory  Rotary

Terminology

Chill  Cope and drag  Core  Draft angle  Dross  Flask  Ingot  Molding sand  Pattern  Riser  Slag  Sprue

Casting  Fabrication  Forming  Jewellery  Machining  Metallurgy  Smithing  Tools & Terminology  Welding

Categories: Casting (manufacturing)Hidden categories: All articles with unsourced statements | Articles with unsourced statements from March 2009 | Articles needing additional references from February 2010 | All articles needing additional references | Articles needing additional references from March 2009 | Articles with unsourced statements from September 2008 | Articles with unsourced statements from February 2009